1. Computer Services
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.grid-itc.com/computer-services
2. Sealed Bearings
Sealed bearings. A selection of SKF spherical roller bearings is also produced in a sealed version with contact seals on both sides. The seals are reinforced with sheet steel and made of an oil and wear-resistant: acrylonitrile-butadiene rubber (NBR), designation suffix 2CS; hydrogenated acrylonitrile butadiene rubber (HNBR), designation suffix 2CS5; fluoro rubber (FKM), designation suffix 2CS2. The seals are inserted in recesses in the outer ring. For smaller bearing sizes, the seals are pressed into the recesses while the seals for the larger sizes are held in position by means of retaining rings (fig). The seals have two sealing lips contacting the lead-in at the sides of the inner ring raceway, to provide efficient sealing. Sealed bearings are lubricated as standard with an extreme pressure bearing grease according to table 1. They should not be heated to temperatures above 80°C during mounting, and should not be washed. Sealed bearings do not need to be relubricated when the operating temperature does not exceed 70°C and the rotational speed is below 50% of the limiting speed listed in the product table. When temperature and/or speeds are high, relubrication with a similar grease with lithium thickener is recommended. In this case the polymer band, which covers the lubrication holes in the outer ring must be removed before mounting. Note that only a small amount of grease is needed to relubricate sealed bearings. The grease should be pressed in slowly through the lubrication holes in the outer ring while the bearing is rotating. Excessive pressure should be avoided so as not to damage the seals. The internal design of a sealed bearing corresponds to that of an open bearing. The external dimensions are also the same except for bearings based on the 222 and 223 series. These bearings are slightly wider and carry the series designation BS2-22 and BS2-23 respectively. Sealed bearings are available with a cylindrical bore as standard. However most bearings in the BS2-22 series are available with a tapered bore as well. Every sealed bearing can be supplied with a tapered bore to special order. To prevent interference with the seal, the diameter of the shaft abutment should not exceed damax at least for the 1 to 2 mm closest to the bearing. If the bearings are secured axially on the shaft by a lock nut, SKF recommends using a KMFE lock nut or to position an intermediate ring between the bearing and the lock nut.
http://ball-bearings.online
3. Press Forging
Press forging works by slowly applying a continuous pressure or force, which differs from the near-instantaneous impact of drop-hammer forging. The amount of time the dies are in contact with the workpiece is measured in seconds (as compared to the milliseconds of drop-hammer forges). The press forging operation can be done either cold or hot. The main advantage of press forging, as compared to drop-hammer forging, is its ability to deform the complete workpiece. Drop-hammer forging usually only deforms the surfaces of the workpiece in contact with the hammer and anvil; the interior of the workpiece will stay relatively undeformed. Another advantage to the process includes the knowledge of the new part's strain rate. We specifically know what kind of strain can be put on the part, because the compression rate of the press forging operation is controlled.
http://press-forging.ktforge.co.uk
4. Volkswagen Car Bearings
Volkswagen, a German automotive manufacturer, has a rich and eventful history that dates back to the 1930s. Volkswagen was founded in 1937 under the German Labour Front, a Nazi trade union, with the goal of producing an affordable "people's car". The company's first model was the iconic Volkswagen Beetle (Type 1), designed by Ferdinand Porsche in 1938. After World War II, Volkswagen's factory in Wolfsburg, Germany, was under British control, but it eventually returned to German ownership. In the 1950s, Volkswagen started exporting Beetles to various countries, including the United States, where it experienced significant success. In the 1970s, Volkswagen expanded its product range beyond the Beetle with the introduction of the Volkswagen Golf (Rabbit in the United States), a compact front-wheel-drive hatchback. Volkswagen acquired other automotive brands, including Audi in 1964, SEAT in 1986, Škoda in 1991, and Bentley, Bugatti, and Lamborghini in the late 1990s. The company also introduced various other successful models, such as the Passat, Jetta, and Polo, catering to different segments of the market. In 2015, Volkswagen faced a major crisis when it was revealed that the company had installed software in its diesel vehicles to cheat on emissions tests, leading to the "dieselgate" scandal. As a result, Volkswagen faced significant financial penalties, legal actions, and a tarnished reputation. In response, Volkswagen has been undergoing a transformation, focusing on electric vehicles (EVs) and sustainable mobility, launching models like the all-electric ID.3 and ID.4.
http://ball-bearings.online/oem/volks/products
5. Roll Forging
Roll forging is a process where round or flat bar stock is reduced in thickness and increased in length. Roll forging is performed using two cylindrical or semi-cylindrical rolls, each containing one or more shaped grooves. A heated bar is inserted into the rolls and when it hits a stop the rolls rotate and the bar is progressively shaped as it is rolled through the machine. The piece is then transferred to the next set of grooves or turned around and reinserted into the same grooves. This continues until the desired shape and size is achieved. The advantage of this process is there is no flash and it imparts a favorable grain structure into the workpiece. Examples of products produced using this method include axles, tapered levers and leaf springs.
http://roll-forging.kt-forge.co.uk
6. Sheffield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.application-development.1tsolutions.com
7. Doncaster Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.doncaster.custom.software.abrt.com
8. Fiat Car Bearings
Fiat, an Italian automobile manufacturer, has a long and storied history that spans over a century. Fiat, short for Fabbrica Italiana Automobili Torino, was founded on July 11, 1899, in Turin, Italy, by a group of investors led by Giovanni Agnelli. Fiat's first car, the Fiat 4 HP, was produced in 1899. It was a small, lightweight vehicle that helped establish Fiat's reputation for engineering and innovation. In the early 1900s, Fiat expanded its production capacity and introduced various models, including the Fiat 500 "Topolino" and the larger Fiat 508 "Balilla". Fiat experienced significant growth during the 1930s and 1940s, becoming the largest automobile manufacturer in Italy. Models such as the Fiat 1100 and the Fiat 500 "Cinquecento," both of which achieved widespread popularity. Fiat expanded internationally, establishing manufacturing facilities in several countries and acquiring other automotive companies like Lancia and Alfa Romeo. In the 1970s, Fiat continued to expand globally, forming partnerships with foreign manufacturers and establishing joint ventures, producing the Fiat Panda, Fiat Uno, and Fiat Tipo. Fiat also formed a partnership with the American manufacturer Chrysler in 2009, leading to the creation of Fiat Chrysler Automobiles (FCA) in 2014. Recent models include the Fiat 500 and the Fiat Panda gaining popularity. Fiat has also embraced electric mobility, introducing electric versions of its models, including the Fiat 500e.
http://ball-bearings.online/oem/fiat/products
9. Stainless Steel Tubing
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
10. Threadolets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.threadolets.zx55.com
11. Upset Forging
Upset forging increases the diameter of the workpiece by compressing its length. Based on number of pieces produced this is the most widely used forging process. A few examples of common parts produced using the upset forging process are engine valves, couplings, bolts, screws, and other fasteners. Upset forging is usually done in special high-speed machines called crank presses, but upsetting can also be done in a vertical crank press or a hydraulic press. The machines are usually set up to work in the horizontal plane, to facilitate the quick exchange of workpieces from one station to the next. The initial workpiece is usually wire or rod, but some machines can accept bars up to 25 cm (9.8 in) in diameter and a capacity of over 1000 tons. The standard upsetting machine employs split dies that contain multiple cavities. The dies open enough to allow the workpiece to move from one cavity to the next; the dies then close and the heading tool, or ram, then moves longitudinally against the bar, upsetting it into the cavity. If all of the cavities are utilized on every cycle then a finished part will be produced with every cycle, which makes this process advantageous for mass production.
http://upset-forging.kt-forge.co.uk
12. Stainless Steel Low Pressure BSP Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.low-pressure-bsp-fittings.stainless-steel.zx55.com
13. Rotherham Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://rotherham.software.devlopment.grid-itc.com
14. Mazda Car Bearings
Mazda Motor Corporation, a Japanese automotive manufacturer, has a compelling history that spans over 100 years. It was established in 1920 as Toyo Cork Kogyo Co., Ltd., initially manufacturing cork products. In the 1930s, the company diversified into producing machine tools and started developing its first prototype vehicles. After World War II, Toyo Kogyo began producing three-wheeled trucks, evolving into its first passenger car, the Mazda R360, in 1960. Mazda gained international recognition in the 1960s for its development of the Wankel rotary engine, known for its compact size and high power output. The Mazda Cosmo Sport, introduced in 1967, was the first production car powered by a rotary engine and became an iconic symbol of Mazda's engineering prowess. In the 1980s, Mazda expanded its presence worldwide, establishing manufacturing facilities and sales networks in various countries. Mazda formed a strategic partnership with Ford Motor Company in 1979, which led to collaboration in areas such as technology sharing and joint vehicle development. During this period, Mazda introduced notable models like the compact Familia/323, the MX-5 Miata sports car, and the 626 mid-size sedan. In the early 2000s, Mazda adopted a design philosophy called "KODO - Soul of Motion," emphasizing dynamic and expressive styling across its model range. Noteworthy models introduced in recent years include the Mazda3, Mazda6, CX-5, and CX-9, featuring innovative technologies and a balance of performance and efficiency.
http://ball-bearings.online/oem/mazda/products
15. Stainless Pipe Supplier
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://stainless-pipe-supplier.zx55.com
16. Stainless Steel Flange Gaskets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.flange-gaskets.stainless-steel.zx55.com
17. Timeken
Timken Bearing Products. Timken is a leader in all bearing types, including standard anti-friction bearing configurations and advanced products such as housed units, integrated bearing assemblies, precision assemblies and FAA-approved aerospace bearings. Timken Roller Bearings, Tapered Roller Bearings, Spherical Roller Bearings, Cylindrical Roller Bearings, Precision Cylindrical Roller Bearings, Needle Roller Bearings, Thrust Roller Bearings, Timken Ball Bearings, Radial Ball Bearings, Angular Contact Bearings, Precision Bearings, Timken Spherical Plain Bearings, Radial Bearings, Radial Bearings with Lip Seals, Angular Contact Thrust Bearings, Timken High Performance Bearings, AquaSpexx® Trailer Wheel Bearing Kits, AquaSpexx® for Industrial Applications, DuraSpexx® and DuraSpexx® Power Rating Series, Thin Dense Chrome Bearings, Debris Resistant Bearings, Wear-Resistant Bearings, Low Torque Bearings, P900 Bearings, Timken Precision Bearings for Machine Tools, Super Precision Ball Bearings, Precision Tapered Roller Bearings, Ball Screw Support Bearings, Hydra-Rib Variable Preload Bearings, Precision Crossed Roller Bearings, Precision Cylindrical Roller Bearings, Timken Aerospace Bearings, Aerospace Ball Bearings, Aerospace Cylindrical Bearings, Aerospace Tapered Roller Bearings, Aerospace Spherical Roller Bearings, Aircraft Landing Wheel Bearings, Timken Integrated Bearing Assemblies, AP™ Integrated Bearing Assemblies, AP-2™ Integrated Bearing Assemblies, Formed Hub Wheel End System.
http://ball-bearings.online
18. Chesterfield Web Design
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://www.chesterfield.web-design.1t-s.com
19. Barnsley Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.barnsley.software.devlopment.abrt.com
20. BMW Car Bearings
BMW (Bayerische Motoren Werke AG) is a German luxury automobile and motorcycle manufacturer known for its high-performance vehicles. BMW was founded on March 7, 1916, initially as an aircraft engine manufacturer named Bayerische Flugzeugwerke. In 1922, BMW began producing motorcycles with the acquisition of Fahrzeugfabrik Eisenach, and in 1928, it expanded into automobile manufacturing by purchasing Fahrzeugfabrik Dixi AG. In the 1930s, BMW gained recognition for producing luxury and sports cars, including the BMW 328, which achieved success in motorsports. During World War II, BMW produced aircraft engines, motorcycles, and military vehicles. In the 1960s, BMW shifted its focus towards luxury automobiles, introducing models like the BMW 1500 and BMW 2002. The BMW "New Class" sedans, launched in the 1960s, played a crucial role in the company's resurgence and reestablished its reputation for sporty, performance-oriented vehicles. In the 1970s, BMW introduced the 3 Series, which became one of the company's most successful and enduring models. In the 1990s, BMW expanded its model range and introduced new technologies, including the introduction of the BMW Z3 roadster and the BMW X5, one of the first luxury SUVs. BMW acquired the British automotive brands Rover and MG in the late 1990s but later sold them off to focus on its core BMW brand. The 2000s saw BMW's expansion into electric and hybrid vehicles with the launch of the BMW i3 and i8. BMW continues to innovate, introducing advanced technologies, performance-oriented models, and expanding its electric vehicle offerings with models like the BMW iX3 and BMW i4.
http://ball-bearings.online/oem/bmw/products
21. Open Die Forging
Open-die forging is also known as smith forging. In open-die forging, a hammer strikes and deforms the workpiece, which is placed on a stationary anvil. Open-die forging gets its name from the fact that the dies (the surfaces that are in contact with the workpiece) do not enclose the workpiece, allowing it to flow except where contacted by the dies. Therefore the operator needs to orient and position the workpiece to get the desired shape. The dies are usually flat in shape, but some have a specially shaped surface for specialized operations. For example, a die may have a round, concave, or convex surface or be a tool to form holes or be a cut-off tool. Open-die forging lends itself to short runs and is appropriate for art smithing and custom work. In some cases, open-die forging may be employed to rough-shape ingots to prepare them for subsequent operations. Open-die forging may also orient the grain to increase strength in the required direction. Cogging is successive deformation of a bar along its length using an open-die drop forge. It is commonly used to work a piece of raw material to the proper thickness.
http://open-die-forging.ktforge.co.uk
22. Forging Stainless Steel
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://forging-stainless-steel.kt-forge.co.uk
23. Barnsley Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.barnsley.custom.software.grid-itc.com
24. Rotherham Computer Services
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.rotherham.computer.service.1t-s.com
25. Sheffield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.application.development.grid-itc.com
26. Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.bespoke.software.1t-s.com
27. 304 Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
28. Hot Forging
Hot forging is the plastic deformation of metal at a temperature and strain rate such that recrystallization occurs simultaneously with deformation, thus avoiding strain hardening. For this to occur, high workpiece temperature (matching the metal's recrystallization temperature) must be attained throughout the process. A form of hot forging is isothermal forging, where materials and dies are heated to the same temperature. In nearly all cases, isothermal forging is conducted on superalloys in a vacuum or highly controlled atmosphere to prevent oxidation.
http://hot-forging.ktforge.co.uk
29. Open Source
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://www.open-source.1t-s.com
30. Barnsley Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.barnsley.software.devlopment.1t-s.com
31. Trailer Bearings
Trailer Bearings for all types of boat trailers - both tapered roller and ball bearings. The most popular bearings fitted to trailers are Tapered Roller Bearings. They come as two separate parts called the cup and cone. Some are supplied with a seal built in as an integral part of the bearing cone. Most bearings are stamped with an identification number by the manufacturer, If there are no numbers then the bearing can be identified by its dimensions - try typing the sizes in the search box. The most common bearings used on boat trailers are L44643 - L44610 and L44643L - L44610 Bearing number L44643 refers to the bearing cone without built in seal as shown on the left in both pictures. Bearing number L44643 L refers to the bearing cone with built in seal as shown on the right in both pictures. The same cup is used for both having the number L44610. Bearings for old style Mini hubs - these use ball bearings of the type 14/LJT 7/8" The bearings are a single row thrust bearing - 2" outside x 7/8" bore x 9/16" wide There are usually two bearings per hub with an oilseal which is 2.1/8" x 1.3/8" x 5/16".We supply both the bearings and oilseal - see our Online shop for prices.
http://ball-bearings.online
32. Barnsley Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.barnsley.application.development.grid-itc.com
33. High Pressure Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.high-pressure-fittings.stainless-steel.zx55.com
34. Needle Roller Bearings
A needle roller bearing is a type of rolling element bearing that uses long, thin cylindrical rollers with a small diameter in proportion to their length. These rollers, known as needle rollers, have a high length-to-diameter ratio, giving them a needle-like appearance and name. Needle roller bearings are designed to support high radial loads with a relatively small cross-sectional area. Needle roller bearings are commonly used in various applications that require compact and lightweight designs with high load-carrying capacity. They are found in automotive transmissions, power tools, motorcycles, industrial machinery, and other equipment where space constraints and high load requirements are present.
http://ball-bearings.online/categories/needle-roller?id_category=17
35. Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://stainless-steel.zx55.com
36. Rotherham Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.rotherham.bespoke-software.1tsolutions.com
37. Contact Management Software
Contact Manager provides a shared database for all your business contact information. Web-enabled for access from anywhere, with a Windows application for remote users supporting on-line and off-line use with advanced synchronisation features.
http://www.1t-s.com/contact-manager
38. Barnsley Open Source
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://www.barnsley.open-source.1t-s.com
39. Barnsley Computer Services
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://barnsley.computer.service.1t-s.com
40. Doncaster Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://doncaster.linux.1t-s.com
41. Rotherham Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.rotherham.custom.software.grid-itc.com
42. Rotherham Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.rotherham.software.devlopment.1t-s.com
43. Sheffield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.sheffield.application.development.grid-itc.com
44. Roll Forging
Roll forging is a process where round or flat bar stock is reduced in thickness and increased in length. Roll forging is performed using two cylindrical or semi-cylindrical rolls, each containing one or more shaped grooves. A heated bar is inserted into the rolls and when it hits a stop the rolls rotate and the bar is progressively shaped as it is rolled through the machine. The piece is then transferred to the next set of grooves or turned around and reinserted into the same grooves. This continues until the desired shape and size is achieved. The advantage of this process is there is no flash and it imparts a favorable grain structure into the workpiece. Examples of products produced using this method include axles, tapered levers and leaf springs.
http://www.kt-forge.co.uk/roll-forging
45. Volvo Car Bearings
Volvo Cars is a Swedish automobile manufacturer known for producing premium vehicles with a focus on safety, innovation, and Scandinavian design. Volvo Cars was founded on April 14, 1927, in Gothenburg, Sweden, as a subsidiary of the ball bearing manufacturer SKF. The first Volvo car, the Volvo ÖV4, also known as the "Jakob," rolled off the production line in 1927. In the 1930s, Volvo introduced the PV series, which included popular models like the PV444 and PV544. During World War II, Volvo temporarily shifted its focus to producing military vehicles and equipment. In 1944, Volvo appointed engineer Nils Bohlin, who invented the modern three-point safety belt, making it a standard feature in Volvo cars. In the 1950s and 1960s, Volvo continued to prioritize safety and introduced various safety innovations, including the laminated windshield and the energy-absorbing crumple zone. Volvo expanded internationally, establishing assembly plants in various countries, including Canada and the United States. In 1970, Volvo Cars was acquired by the Ford Motor Company. Under Ford's ownership, Volvo saw further expansion and development. Volvo introduced iconic models such as the Volvo 240, Volvo 740, and Volvo 850, known for their safety features and reliability. In 2010, Ford sold Volvo Cars to Zhejiang Geely Holding Group, a Chinese automotive company. Under Geely's ownership, Volvo Cars underwent a rejuvenation, focusing on modern design, technological innovation, and sustainability. Volvo introduced the SPA (Scalable Product Architecture) platform, which underpins its current vehicle lineup and enables electrification. The company has been committed to electric mobility and launched its first fully electric vehicle, the Volvo XC40 Recharge, in 2020. Volvo Cars aims to become a leader in sustainable mobility, with a plan to be a fully electric car company by 2030.
http://ball-bearings.online/oem/volvo/products
46. Waste Recycling System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-recycling-system.skip-manager.co.uk
47. Ball Bearings
A ball bearing is a type of rolling element bearing that consists of a series of hardened steel balls or ceramic balls. It is designed to reduce friction between rotating parts and support radial and axial loads. Ball bearings are commonly used in various applications, including automotive components, industrial machinery, household appliances, electric motors, and many other mechanical systems. They are available in different sizes and configurations to accommodate different load capacities, speeds, and operating conditions.
http://ball-bearings.online/categories/ball-bearings?id_category=9
48. Huddersfield University Student Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/huddersfield-university-student-accomodation
49. Computer Support
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://1t-s.com/computer-support
50. Chesterfield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.application.development.1t-s.com
51. Y-bearings with an eccentric locking collar
Y-bearings with an eccentric locking collar are intended primarily for use in applications where the direction of rotation is constant. On one side of the bearing inner ring is an eccentric extension that fits the locking collar. Turning the locking collar on the inner ring extension in the direction of rotation locks the collar and the bearing onto the shaft. A single grub (set) screw further secures the collar to the shaft. There are two standard series available from SKF: Y-bearings in the YET 2 series have an extended inner ring on one side and are fitted with the rugged "Superagriseal" on both sides. The eccentric collar is zinc-coated. The outer ring has two lubrication holes as standard. Y-bearings in the YEL 2 series have an extended inner ring on both sides . This reduces the extent to which the inner ring can tilt on the shaft, which allows the bearing to run more smoothly. These bearings are fitted with the rugged "Superagriseal", and one of the following flinger options
http://ball-bearings.online?pg=rb-yb-elc
52. Sanitary Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://sanitary-fittings.stainless-steel.zx55.com
53. ZX55.com
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
54. Skip Hire System
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://skip-hire-system.skip-manager.co.uk
55. Scooter Bearings
If you have plastic core scooter wheels then fitting the bearings is very straight forward as they typically can be pushed in by hand without issue. Fitting scooter bearings into Metal core wheels is a little trickier as they are designed to be a tight fit so pushing them in by hand rarely works. In our workshop we used to use a vise to gently squeeze them in, but now we use a hammer!! Apply a small amount of grease to the edges of each bearing you are going to install. Apply a small amount of grease to the inside hole on the scooter wheel where the bearings are going to be fitted. Place the bearing over the hole in the wheel and try and make sure that it is straight/level as possible. Place either a block of wood or an old paperback book over the top of the bearing and gently strike this with the hammer (Important - do not strike the bearing directly with the hammer). When the bearing has been hammered in fully into the hole in the middle of your wheel it should sit flush with the edge of the wheel Turn the wheel over and insert the bearing spacer (you will need a bearing spacer, if you do not use one your wheel will not spin when you do your axles up securely!)
http://ball-bearings.online
56. Waste Management Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-management-software.skip-manager.co.uk
57. Chesterfield Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.custom.software.1t-s.com
58. Doncaster Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.application.development.abrt.com
59. Y-bearings with a standard inner ring
Y-bearings in the 17262(00)-2RS1 and 17263(00)-2RS1 series , with a standard inner ring, have Normal tolerances for the bearing bore diameter and are located on the shaft using an appropriate interference fit. The only difference between these Y-bearings and deep groove ball bearings in the 62 or 63 series is the sphered outside surface of the outer ring. These Y-bearings are suitable for applications where smooth running is a key operating requirement. These bearings can accommodate heavier axial loads than Y-bearings of any other design. The SKF range comprises bearings for metric shafts from 17 to 60 mm.
http://ball-bearings.online?pg=rb-yb-sir
60. Rotherham Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.rotherham.bespoke.software.abrt.com
61. Stainless Steel Pipes
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.pipes.stainless-steel.zx55.com
62. Single row deep groove ball bearings
Single row deep groove ball bearings are particularly versatile. They are simple in design, non-separable, suitable for high and even very high speeds and are robust in operation, requiring little maintenance. Deep raceway grooves and the close conformity between the raceway grooves and the balls enable deep groove ball bearings to accommodate axial loads in both directions, in addition to radial loads, even at high speeds.
http://ball-bearings.online?pg=rb-dgbb-sr
63. Chesterfield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.application-development.1tsolutions.com
64. Low Pressure Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://low-pressure-fittings.stainless-steel.zx55.com
65. Rotherham Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://www.rotherham.linux.1t-s.com
66. Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://abrt.com/custom-software
67. SKF Bearings
Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland
http://www.steelcitybearings.com
68. South Yorkshire Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.custom.software.abrt.com
69. Ball and Roller Bearings
A rolling-element bearing, also known as a rolling bearing, is a bearing which carries a load by placing round elements between two bearing rings. The relative motion of the pieces causes the round elements to roll with very little rolling resistance and with little sliding. One of the earliest and best-known rolling-element bearings are sets of logs laid on the ground with a large stone block on top. As the stone is pulled, the logs roll along the ground with little sliding friction. As each log comes out the back, it is moved to the front where the block then rolls on to it. It is possible to imitate such a bearing by placing several pens or pencils on a table and placing an item on top of them. See "bearings" for more on the historical development of bearings. A rolling element rotary bearing uses a shaft in a much larger hole, and cylinders called "rollers" tightly fill the space between the shaft and hole. As the shaft turns, each roller acts as the logs in the above example. However, since the bearing is round, the rollers never fall out from under the load.
http://ball-bearings.online
70. Chesterfield Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.custom.software.grid-itc.com
71. Waste Recycling Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://waste-recycling-software.skip-manager.com
72. South Yorkshire Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://south-yorkshire.custom.software.1t-s.com
73. IP WhoIs
The Detailed WhoIs tool not only checks the domain or IP address you request, but also looks up details of any associated domains and IP addresses, building a comprehensive report.
http://whois.1t-s.com
74. Hammer Forging
The most common type of forging equipment is the hammer and anvil. Principles behind the hammer and anvil are still used today in drop-hammer equipment. The principle behind the machine is simple: raise the hammer and drop it or propel it into the workpiece, which rests on the anvil. The main variations between drop-hammers are in the way the hammer is powered; the most common being air and steam hammers. Drop-hammers usually operate in a vertical position. The main reason for this is excess energy (energy that isn't used to deform the workpiece) that isn't released as heat or sound needs to be transmitted to the foundation. Moreover, a large machine base is needed to absorb the impacts. To overcome some shortcomings of the drop-hammer, the counterblow machine or impactor is used. In a counterblow machine both the hammer and anvil move and the workpiece is held between them. Here excess energy becomes recoil. This allows the machine to work horizontally and have a smaller base. Other advantages include less noise, heat and vibration. It also produces a distinctly different flow pattern. Both of these machines can be used for open-die or closed-die forging. A forging press, often just called a press, is used for press forging.
http://www.ktforge.co.uk/hammer-forging
75. Needle Bearings
Needle roller bearings are roller bearings with cylindrical rollers that are small in diameter. In spite of their low cross section, needle roller bearings have a high load carrying capacity and are therefore extremely suitable for bearing arrangements where radial space is limited. SKF supplies needle roller bearings in different designs and a wide range of sizes, which are appropriate for different applications. In addition to customized designs, they comprise the following types and components: needle roller and cage assemblies); drawn cup needle roller bearings; with open ends and with a closed end; full complement with open ends; needle roller bearings with machined rings; with flanges (closure rings or integral flanges) on the outer ring, sealed or not sealed and with or without an inner ring; without flanges on the outer ring , not sealed and with or without an inner ring; alignment needle roller bearings; with and without an inner ring ; inner rings for needle roller bearings ; universal joint bearings ; needle rollers; combined needle roller bearings (separate section); needle roller / angular contact ball bearings ; needle roller / thrust ball bearings ; needle roller / cylindrical roller thrust bearings ; needle roller thrust bearings and bearing washers (separate section); needle roller and cage thrust assemblies and appropriate washers; needle roller thrust bearings with a centring spigot and appropriate washers
http://ball-bearings.online
76. Hygienic Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
77. Huddersfield University Student Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/huddersfield-university-student-accomodation
78. Computer Support
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://abrt.com/computer-support
79. Skip Manager
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://skip-manager.com
80. House For Rent Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/house-for-rent-huddersfield
81. Barnsley Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.barnsley.bespoke.software.abrt.com
82. Hot Forming
Hot forging is the plastic deformation of metal at a temperature and strain rate such that recrystallization occurs simultaneously with deformation, thus avoiding strain hardening. For this to occur, high workpiece temperature (matching the metal's recrystallization temperature) must be attained throughout the process. A form of hot forging is isothermal forging, where materials and dies are heated to the same temperature. In nearly all cases, isothermal forging is conducted on superalloys in a vacuum or highly controlled atmosphere to prevent oxidation.
http://hot-forming.kt-forge.co.uk
83. Huddersfield University Student Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/huddersfield-university-student-accomodation
84. Bespoke Accounts Software
Download Ice Ledger accounts system now for free and get started. Fully featured, multi-currency accounts with Sales, Purchase and Nominal ledgers, Sales and Purchase Invoicing, Stock Control and more...
http://iceledger.com/
85. Stainless Pipe Supplier
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
86. Rod End Bearings
Spherical plain bearings and rod ends. In addition to ball and roller bearings SKF also produces a comprehensive range of spherical plain bearings and rod ends and has a choice of materials for plain and flanged bushings as well as thrust washers. Spherical plain bearings and rod ends are produced in various designs and with various combinations of sliding contact surfaces. Each design and combination has characteristic properties which make it particularly suitable for certain applications. To select a certain bearing type and to establish the requisite bearing size, the main factors which have to be considered are the loads, the load carrying capacity of the bearing and the expected service life. The same is true when selecting a rod end. Selection of bearing type. The choice of the appropriate type of bearing (radial, angular contact or thrust) is determined by the direction of the load which will act on the bearing, while the choice of the appropriate sliding contact surface combination is primarily determined by the way in which the load acts (constant or alternating direction). Radial load: When the load is purely or predominantly radial, a radial spherical plain bearing should be selected. These bearings can accommodate a certain amount of axial load in addition to the radial load. Axial load: When the load is purely or predominantly axial then the choice should be a spherical plain thrust bearing. These bearings can accommodate a certain proportion of radial load in addition to the axial load.
http://ball-bearings.online
87. Stainless Steel Valves
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
88. Steel Forging
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.ktforge.co.uk/steel-forging
89. Doncaster Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.software.devlopment.1t-s.com
90. Doncaster Open Source
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://doncaster.open-source.1t-s.com
91. Chesterfield Open Source
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://www.chesterfield.open-source.1t-s.com
92. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.software.development.1t-s.com
93. Steel Forging
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.kt-forge.co.uk/steel-forging
94. eCommerce
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://www.1t-s.com/internet-web-design
95. Huddersfield University Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4share.co.uk/huddersfield-university-accomodation
96. Deep Groove Bearings
A deep groove bearing, also known as a deep groove ball bearing, is a type of rolling element bearing that is widely used in various applications. It is named for its deep, uninterrupted raceway grooves on both the inner and outer rings, which enable it to accommodate radial loads, axial loads, and combined loads. Deep groove bearings are designed to reduce friction and provide smooth operation. The raceway grooves facilitate the rolling motion of the balls, allowing them to distribute the load evenly. This design enables deep groove bearings to handle both radial and axial loads with low friction and minimal power loss.
http://ball-bearings.online/categories/deep-groove?id_category=16
97. Chesterfield Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.bespoke-software.1tsolutions.com
98. South Yorkshire Computer Services
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://south-yorkshire.computer.service.1t-s.com
99. Skip Hire Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://skip-hire-software.skip-manager.co.uk
100. Engineering Blacksmiths
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://www.kt-forge.co.uk/engineering-blacksmiths
101. WhoIs
The Detailed WhoIs tool not only checks the domain or IP address you request, but also looks up details of any associated domains and IP addresses, building a comprehensive report.
http://whois.1t-s.com
102. Chesterfield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://chesterfield.software.devlopment.grid-itc.com
103. Stainless Steel Flanges
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.flanges.stainless-steel.zx55.com
104. Threadolets
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
105. Butt-Weld Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
106. Stainless Steel Forging
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://stainless-steel-forging.kt-forge.co.uk
107. Stainless Steel Butt-Weld Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
108. Drop Forging
Drop forging is a metal shaping process, the metal to be formed is first heated then shaped by forcing it into the contours of a die, this force can be in excess of 2000 tons. The drop forging process can be performed with the material at various temperatures. Hot Forging: During hot forging the metals are heated to above their recrystallization temperature. The main benefit of this hot forging is that work hardening is prevented due to the recrystallization of the metal as it begins to cool. Cold Forging: Cold Forging is generally performed with metal at room temperature below the the recrystallization temperature. Cold forging typically work hardens the metal. There are two types of drop forging, open die and closed die. Open die drop forging requires the operator to position the work piece while it is impacted by the ram. The die attached to the ram is usually flat or of a simple contour, most of the shaping is achieved by the operator physically positioning the work piece before each stroke of the ram. There are also special dies which can be used to cut the metal, form holes or notches.
http://drop-forging.ktforge.co.uk
109. Bearings
Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland
http://www.steelcitybearings.com
110. Drop Forging
Drop forging is a metal shaping process, the metal to be formed is first heated then shaped by forcing it into the contours of a die, this force can be in excess of 2000 tons. The drop forging process can be performed with the material at various temperatures. Hot Forging: During hot forging the metals are heated to above their recrystallization temperature. The main benefit of this hot forging is that work hardening is prevented due to the recrystallization of the metal as it begins to cool. Cold Forging: Cold Forging is generally performed with metal at room temperature below the the recrystallization temperature. Cold forging typically work hardens the metal. There are two types of drop forging, open die and closed die. Open die drop forging requires the operator to position the work piece while it is impacted by the ram. The die attached to the ram is usually flat or of a simple contour, most of the shaping is achieved by the operator physically positioning the work piece before each stroke of the ram. There are also special dies which can be used to cut the metal, form holes or notches.
http://drop-forging.kt-forge.co.uk
111. Rotherham Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://rotherham.custom.software.grid-itc.com
112. Rotherham eCommerce
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://www.1t-s.com/internet-web-design
113. Ball Bearings
The purpose of a ball bearing is to reduce rotational friction and support radial and axial loads. It achieves this by using at least two races to contain the balls and transmit the loads through the balls. In most applications, one race is stationary and the other is attached to the rotating assembly (e.g., a hub or shaft). As one of the bearing races rotates it causes the balls to rotate as well. Because the balls are rolling they have a much lower coefficient of friction than if two flat surfaces were sliding against each other. Ball bearings tend to have lower load capacity for their size than other kinds of rolling-element bearings due to the smaller contact area between the balls and races. However, they can tolerate some misalignment of the inner and outer races.
http://ball-bearings.online
114. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.software.development.abrt.com
115. Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.1tsolutions.com/bespoke-software
116. Sanitary Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
117. Sheffield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.sheffield.software.devlopment.1tsolutions.com
118. Roll Forging
Roll forging is a process where round or flat bar stock is reduced in thickness and increased in length. Roll forging is performed using two cylindrical or semi-cylindrical rolls, each containing one or more shaped grooves. A heated bar is inserted into the rolls and when it hits a stop the rolls rotate and the bar is progressively shaped as it is rolled through the machine. The piece is then transferred to the next set of grooves or turned around and reinserted into the same grooves. This continues until the desired shape and size is achieved. The advantage of this process is there is no flash and it imparts a favorable grain structure into the workpiece. Examples of products produced using this method include axles, tapered levers and leaf springs.
http://www.ktforge.co.uk/roll-forging
119. Bike Bearings
Taking good care of your mountain bike is of paramount importance. Mountainbikebearings.co.uk stock all types of mountain bike bearings including bottom bracket bearings, pivot bearings, headset bearings, hub bearings, we also have in stock DU bushes which are found in shocks. We offer the mountain bike bearings as a standard bearing, or stainless steel bearing in most applications. Mountain Bike Bearings also offer bearings in various makes such as SKF and INA. We also stock a lot of genuine Hope bearings for pro 2 and pro 3 hubs, headsets and bottom brackets, and we have a budget range for when price is an issue. These can all be purchased from our online shop with next day delivery direct from our warehouse.
http://ball-bearings.online
120. Upset Forging
Upset forging increases the diameter of the workpiece by compressing its length. Based on number of pieces produced this is the most widely used forging process. A few examples of common parts produced using the upset forging process are engine valves, couplings, bolts, screws, and other fasteners. Upset forging is usually done in special high-speed machines called crank presses, but upsetting can also be done in a vertical crank press or a hydraulic press. The machines are usually set up to work in the horizontal plane, to facilitate the quick exchange of workpieces from one station to the next. The initial workpiece is usually wire or rod, but some machines can accept bars up to 25 cm (9.8 in) in diameter and a capacity of over 1000 tons. The standard upsetting machine employs split dies that contain multiple cavities. The dies open enough to allow the workpiece to move from one cavity to the next; the dies then close and the heading tool, or ram, then moves longitudinally against the bar, upsetting it into the cavity. If all of the cavities are utilized on every cycle then a finished part will be produced with every cycle, which makes this process advantageous for mass production.
http://www.ktforge.co.uk/upset-forging
121. Rotherham Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://rotherham.application.development.grid-itc.com
122. 316 Stainless Steel
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
123. SKF Energy Efficient (E2) deep groove ball bearings
The new SKF Energy Efficient deep groove ball bearings are designed to improve machine efficiency and to save energy, see presentation Energy Efficient solutions. These bearings belong to SKF E2 performance class family, providing: optimized internal geometry for reduced friction, a shield on both sides to protect the friction-reducing features, new cage design, unique lubricant, The designation follows the basic SKF designation system. To clearly show the new performance the prefix "E2." has been added. SKF Energy Efficient bearings are supplied in a new standard box.
http://ball-bearings.online?pg=rb-dgbb-e2
124. Stainless Steel Pipes
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
125. Bearings
Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland
http://www.steelcitybearings.com
126. Press Forging
Press forging works by slowly applying a continuous pressure or force, which differs from the near-instantaneous impact of drop-hammer forging. The amount of time the dies are in contact with the workpiece is measured in seconds (as compared to the milliseconds of drop-hammer forges). The press forging operation can be done either cold or hot. The main advantage of press forging, as compared to drop-hammer forging, is its ability to deform the complete workpiece. Drop-hammer forging usually only deforms the surfaces of the workpiece in contact with the hammer and anvil; the interior of the workpiece will stay relatively undeformed. Another advantage to the process includes the knowledge of the new part's strain rate. We specifically know what kind of strain can be put on the part, because the compression rate of the press forging operation is controlled.
http://www.kt-forge.co.uk/press-forging
127. IT Support
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.1t-s.com/service
128. Rotherham Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://rotherham.bespoke.software.1t-s.com
129. Huddersfield University Accomodation
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/huddersfield-university-accomodation
130. Sheffield Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://sheffield.software.devlopment.grid-itc.com
131. Washing Machine Bearings
How to fit new drum bearings to a washing machine. The drum bearings sit at the back behind the drum and allow the whole things to spin nice and smoothly. So how do you know if you need new drum bearings? Well one customer described it sounding like a concrete mixer on overdrive; it can make a real racket if the drum bearings have gone. The other thing is to look for the amount of movement between the drum and the outer tube. Now the bearings on this machine are fine, you can see there is no real movement there. But if your bearings have gone, the inner drum will move a lot in relation to the outer tub. So here we have the front bearing, the rear bearing and the bearing seal, and they come as a complete set for this Bosch machine. You may find that for your make and model you do need to buy them separately, but do buy all three as we want to replace the lot. We also have a tub seal in this set, because we going to need to remove the whole tub, split it in two and when we put that back together again it's important that we put a new seal on so that it's nice and water-tight. Now this is a big job, not for the feint hearted , you are going to need a little bit of space to work in, but it's going to save you a fortune compared with buying a new machine or calling out an engineer. Safety first, make sure you are unplugged from the mains. So let's get on with removing the tub from the machine.
http://ball-bearings.online
132. Contact Software
Contact Manager provides a shared database for all your business contact information. Web-enabled for access from anywhere, with a Windows application for remote users supporting on-line and off-line use with advanced synchronisation features.
http://www.1t-s.com/contact-manager
133. Bearing NSK
Single-Row Deep Groove Ball Bearings. Pressed Steel Cages. Single-row deep groove ball bearings are the most common type of rolling bearings. Their use is very widespread. In addition to open type bearings, these bearings often have steel shields or rubber seals installed on one or both sides and are prelubricated with grease. Also, snap rings are sometimes used on the periphery. As to cages, pressed steel ones are the most common. For big deep groove ball bearings, machined brass cages are used. Machined cages are also used for high speed applications.
http://ball-bearings.online
134. Doncaster Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.application.development.grid-itc.com
135. Koyo Bearings
KOYO brand bearings from JTEKT are found virtually anywhere where accurate rotational control is required. Bearing applications vary from jet engine main shaft support, manufacturing equipment used to produce semiconductors and LCD displays, through modern windmills, automobiles, high-speed trains and agricultural machinery to medical equipment, drilling machines at your dentist's surgery and various appliances at your household. We are proud to say: our bearings are found from the heights of the stratosphere to the depths of the ocean - many specially developed to function with optimum efficiency in harsh environments such as weightless or extremely corrosive conditions. In short, you will find Koyo bearings wherever there is a need for innovative engineering and reliability that will last.
http://ball-bearings.online
136. Barnsley Software Development
Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.barnsley.software.devlopment.grid-itc.com
137. Steel City Bearings
Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland
http://www.steelcitybearings.com
138. Bearing Suppliers
ZX55.com brings a totally refreshing concept to the way you purchase your bearings and power transmission products. With over 40,000+ bearings in stock, we ship bearings the same day for next day delivery - providing the best quality product at the best possible price. We carry from stock all types of bearings, including deep groove ball bearings, roller bearings, metric and imperial bearings, tapered roller bearings, spherical bearings and needle bearings - plus many more. We also stock all types of chains and sprockets, taper bushes, oil seals and O-rings, airline fittings, braided hose, oils, greases and lubricants, as well as all types of lubrication equipment. In addition, we supply industrial tools, V-belts and wedge belts, timing belts and HTD belts and also offer a belt making service for all types of flat belts.
http://ball-bearings.online
139. Open Die Forging
Open-die forging is also known as smith forging. In open-die forging, a hammer strikes and deforms the workpiece, which is placed on a stationary anvil. Open-die forging gets its name from the fact that the dies (the surfaces that are in contact with the workpiece) do not enclose the workpiece, allowing it to flow except where contacted by the dies. Therefore the operator needs to orient and position the workpiece to get the desired shape. The dies are usually flat in shape, but some have a specially shaped surface for specialized operations. For example, a die may have a round, concave, or convex surface or be a tool to form holes or be a cut-off tool. Open-die forging lends itself to short runs and is appropriate for art smithing and custom work. In some cases, open-die forging may be employed to rough-shape ingots to prepare them for subsequent operations. Open-die forging may also orient the grain to increase strength in the required direction. Cogging is successive deformation of a bar along its length using an open-die drop forge. It is commonly used to work a piece of raw material to the proper thickness.
http://www.ktforge.co.uk/open-die-forging
140. Student Diggs in Huddersfield
4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.
http://www.iam4rent.co.uk/student-diggs-huddersfield
141. Sanitary Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
142. Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://1t-s.com/bespoke-software
143. Skip Hire Software
Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.
http://www.skip-hire-software.com
144. South Yorkshire Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.south-yorkshire.bespoke.software.1t-s.com
145. Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://application.development.1t-s.com
146. Free Accounts Software
Download Ice Ledger accounts system now for free and get started. Fully featured, multi-currency accounts with Sales, Purchase and Nominal ledgers, Sales and Purchase Invoicing, Stock Control and more...
http://iceledger.com/
147. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.software.development.grid-itc.com
148. Computer Maintenance
Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.
http://www.grid-itc.com/computer-maintenance
149. Doncaster Bespoke Software
Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://doncaster.bespoke.software.1t-s.com
150. Doncaster Web Design
Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.
http://doncaster.web-design.1t-s.com
151. Stainless Steel Tubing
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.tubing.stainless-steel.zx55.com
152. Rotherham Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.rotherham.application.development.grid-itc.com
153. Custom Software
Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://grid-itc.com/custom-software
154. Software Development
Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.software-development.1tsolutions.com
155. Linux
1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.
http://www.linux.1t-s.com
156. Stainless Steel High Pressure Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://www.zx55.com
157. Accounts Software for Stockists
Designed for steel stock holders, SASS is a muli-currency accounts system which is ideal for all stockists incorporating Sales, Purchase & Nominal ledgers, Stock Control with emphasis traceability and profits based on actual / real costs ...
http://steelaccounts.com/
158. Chesterfield Application Development
Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.
http://www.chesterfield.application.development.grid-itc.com
159. Forging Stainless Steel
Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.
http://forging-stainless-steel.ktforge.co.uk
160. Stainless Steel Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://fittings.stainless-steel.zx55.com
161. Stainless Steel Hygienic Fittings
ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.
http://zx55.com
South Yorkshire Custom Software - Stainless Steel Forging - Koyo Bearings - Computer Repair - Huddersfield University Accomodation - Ball and Roller Bearings
Barnsley Linux - Stainless Steel Flanges - South Yorkshire Custom Software - Steel Forging - Student Accomodation in Huddersfield - Bike Bearings
Barnsley Custom Software - Doncaster Software Development - Waste Collection System - Student Accomodation Huddersfield - Custom Software - South Yorkshire Application Development
Stainless Steel Gaskets - Sheffield Bespoke Software - Application Development - Application Development - Sheffield Application Development - Application Development
IT Services - Doncaster Custom Software - - Cold Forging - Computer Repair - Volkswagen Car Bearings
Application Development - Chesterfield Application Development - Barnsley Bespoke Software - Barnsley Custom Software - Computer Support - Swaging
Barnsley Software Development - Namaz Times - Huddersfield University Student Accomodation - Cold Forming - Rooms For Rent Huddersfield - Stainless Steel Tubing
South Yorkshire Application Development - Bulk Bearings - Ball Bearings - Forging Stainless Steel - Open Die Forging - South Yorkshire Computer Services
SKF Bearings - Chesterfield Bespoke Software - Waste Management System - Computer Support - Student Accomodation in Huddersfield - Doncaster Custom Software
Hammer Forging - Open Die Forging - Press Forging - Drop Forging - Stainless Steel Flanges - Double row deep groove ball bearings
Stainless Pipe Supplier - Doncaster Linux - Stainless Tube Supplier - Steel Forging - Huddersfield University Student Accomodation - Student Accomodation in Huddersfield
Student Accomodation Huddersfield - Student Accomodation in Huddersfield - South Yorkshire Software Development - Application Development - House For Rent Huddersfield - Software Development
Stainless Steel Hygienic Fittings - South Yorkshire Web Design - Chesterfield Custom Software - Stainless Steel Valves - Press Forging - Sanitary Fittings
Stainless Pipe Supplier - Chesterfield Bespoke Software - Forging Stainless Steel - Stainless Steel - Rotherham Bespoke Software - Web Design
Rotherham Software Development - Sheffield Application Development - Chesterfield Open Source - Low Pressure Fittings - Chesterfield Application Development - Stainless Steel Tubing
Student Diggs in Huddersfield - Application Development - Drop Forging - Barnsley eCommerce - Bespoke Software - Waste Recycling Software
Stainless Steel Low Pressure BSP Fittings - South Yorkshire Bespoke Software - Open Source - Huddersfield Student Housing - Barnsley Software Development - Skip Hire News
Waste Recycling Software - House For Rent Huddersfield - Computer Maintenance - South Yorkshire Open Source - Chesterfield Application Development - Sheffield Computer Services
South Yorkshire Software Development - Salaat Times - Web Design - Bespoke Software - Software Development - Sanitary Fittings
Cold Forging - Surplus Bearings - Stainless Steel Flange Gaskets - Ice Ledger, the first full accounting software for start-up companies - Mazda Car Bearings - Application Development
Barnsley Software Development - Rotherham Application Development - Chesterfield Custom Software - Chesterfield Web Design - Sheffield Application Development - Computer Repair
Rotherham Application Development - Sheffield Application Development - Chrysler Car Bearings - Stainless Steel High Pressure Fittings - Car Wheel Bearings - Doncaster Application Development
South Yorkshire Web Design - Rooms For Rent Huddersfield - Rotherham Bespoke Software - Washing Machine Bearings - Student Diggs in Huddersfield - Waste Collection System
Custom Software - Chesterfield Software Development - Press Forging - Sheffield Custom Software - Rotherham Application Development - Barnsley Computer Services
Student Diggs in Huddersfield - Roll Forging - Huddersfield University Accomodation - Rotherham Bespoke Software - Iveco Truck Bearings - Smith Forging
Rotherham Software Development - Computer Support - South Yorkshire Bespoke Software